淺談轉子秤的部分備件的選擇、秤的使用維護

來 源：www.hfztjd.com    發布時間：2017-9-1 9:35:06

1、上下密封板轉子平衡，轉子精度。設備在更換備件時，應盡量安裝高精度轉子和上下密封板，并做到/更換，并在轉子控制過程中使用上下密封板之間的間隙，減少在風中的比例。由于資金預算問題，有的公司使用轉子精度不高，使用后煤炭開始出現破碎，被迫更換原來的轉子，精度高，更換后出現破碎煤問題。

?

2、通風匹配轉子秤。使用過程中包管入口管風轉子秤滿足三米管道速度風速校準的設計要求，風速V、V、V / 2，以平等和平等的固氣壓力減風率的統一，包管煤粉的正常運輸。??
3、運行期間的檢查和維護轉子秤。轉子平衡帶不能滑動，經常檢查磨損情況，包管驅動輪與從動輪線速度一致。在生產過程中還可以利用機械手工具動態調節轉子尺度間隙，剛打開、潮濕、著火的煤粉破碎煤可適當擴大間隙，正常生產，合理控制轉子尺度間隙在20～25路。??
4、傳感器的檢查。在運行過程中，及時檢查轉子秤如煤等異物，包管傳感器的正常使用。5的標準校準。轉子秤。在標準時間內，開羅風機在轉子尺度的使用過程中，應將轉子內積聚的煤炭吹出，以減少零漂現象。
1. rotor balance of the upper and lower sealing plate, rotor precision. Equipment in the replacement of spare parts, should try to install high precision rotor and the upper and lower sealing plate, and to achieve complete replacement, and rotor control in the process of using the upper and lower sealing gap between the plates, reduce in scale on the wind. Funds due to budget problems, some companies use the rotor of low precision, the use of coal began to appear after breaking, forced to replace the original rotor with high accuracy, after the replacement of broken coal problem. ??
Ventilation matching of 2. rotor scales. Use the process to ensure the entrance duct wind rotor scale to meet the design requirements of three meter pipeline speed calibrated by wind speed, the wind speed is V, V, V/2, to the unity of equal and equal ratio of solid to gas pressure reducing on the wind, to ensure the normal transportation of pulverized coal. ??
Inspection and maintenance during operation of 3. rotor scale. The rotor balance belt can not slide, often check the wear condition, and ensure the driving wheel and the driven wheel line speed is consistent. In the production process also can use the manipulator tools to dynamically adjust the rotor scale gap, just opened, moisture, ignition of pulverized coal broken coal can be properly enlarged the gap, the normal production, reasonable control of rotor scale gap in 20~25 road. ??
4. sensor inspection. In the process of running, timely check the rotor scales such as coal and other foreign bodies, and ensure the normal use of sensors. Standard calibration of 5. rotor scale. In the standard timing, the Cairo fan should blow up the accumulated coal inside the rotor to reduce the zero drift phenomenon during the use of the rotor scale.

合肥卓泰機電是專業從事：煤粉轉子秤及配件、粉體轉子秤、HRM立磨配件、HFCG輥壓機配件、N-TGD鋼絲膠帶提升機配件、煙氣監控的生產和銷售。

官方網站：http://www.jlj3xe.cn